In my 210 gallon tank I use 1 Uniclife 3400 GPH Wave Maker which has adjustable power and wave form settings as well as night mode. I use a Freesea 1600 GPH Wave Maker on top near the surface and a SunSun JVP 800 GPH Wave Maker on the bottom of my 75 Gallon tank. I only turn them off during feedings just so that food doesn’t get sucked into my filters before the boys have had a chance to eat it….and that only stays off for about 2 minutes or less. I keep my wave makers on 24/7 365 days a year. If they do, like my African Cichlids, I can tell you what I do but I’m sure everyone will have there preferred method. Well like I said, research your type of fish first to find out if they enjoy water with current and flow. How To Use Wave Maker In AquariumĪ common question I get asked a lot is how do I use a fish tank wave maker? How long do I leave them on, should you vary the flow, do I turn them off at night? If your fish can handle the current, 2 is better than 1. This will just help in creating and keeping that circular pattern of water movement in your tank. This second wavemaker will go on the opposite side as your first but on the bottom this time. Now if you have a tank on the bigger side, something like a 75 gallon or bigger you might want to add a second wavemaker. If you have a sponge filter the sponge will catch and trap it there too. That’s where your intake strainers will intercept the waste and get sucked right into your filters. All the uneaten food, waste and debris sitting on your substrate will also be pulled towards it from the bottom. The reason is because as the wave maker pushes water away from it on top, it is also pulling water towards it from the bottom. For filter comparison, here’s a great article on best aquarium filters. Since our wave maker will be on top the best side is the same side your intake is on. The intake strainers are at the bottom and a sponge filter sits on your substrate. Whether you have an HOB, a Canister filter, or even just a Sponge filter…water enters those filters from the bottom of your tank. But which side of your tank it goes on will depend on what side your filters intake strainer is. So what’s the best wave maker position in your tank? Well we’ve already discussed that on top angled upwards is super beneficial for surface agitation. How To Setup Aquarium Wave Maker Position The constant current in the tank keeps them distracted and more focused on swimming than each other. This is essential in keeping a healthy environment for your fish as well as maintaining crystal clear water.Īnother great benefit of a wave maker is its ability to reduce aggression in aggressive fish. This will eliminate dead spots in your tank and dislodge any trapped waste or other organic material, helping it to eventually find your filters intake. It can even find a dead spot in your tank where it may never be able to reach your filters intake.Ī wave maker helps with this by constantly creating water movement in your tank. When detritus build up in your tank it can easily get stuck behind or under a piece of décor. No judgement though, I’ve had that guy too □Ī wave maker will also help to keep your water crystal clear. These constant waves on your surface will oxygenate your tank water more efficiently than any scuba diver man with some bubbles. The flow will create waves on your surface which will help in the transfer of oxygen into your tank which is very important. Benefits Of A Wave Maker In AquariumĪ major benefit of a wave maker in an aquarium, if placed on top of your tank and angled upwards towards the surface is the addition of surface agitation. These dead spots are where most of your detritus accumulates.Īfrican Cichlids like my guys love a good current, and a wave maker actually helps in reducing aggression by keeping them busy and actively swimming around instead of expelling all their energy onto another fish.īut some fish like goldfish or bettas don’t like any current at all. Keeping in mind that the more décor in the tank the more dead spots may arise. Make sure that you have adequate hiding spots for your fish to escape the current if they need to rest. Do a little testing and experimenting with how much flow they like or don’t like. If they’re stuck all the way on the other side of the tank they’re trying to get away from it. How can you tell if they like it? If your fish are constantly swimming into the current, they like it. If you have fish that like a good current, a wave maker helps in producing that strong flow of water. But adding a wave maker can be very beneficial for certain tank/fish setups. Having an air pump with an air stone or even a simple sponge filter setup will provide surface agitation for proper oxygen transfer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |